
Video
About the company
The ICAPLAST plant was founded in 1999. Today, the company is the largest and most technologically advanced manufacturer of polymer pipes in Northwest Russia. IСAPLAST produces polymer pipes and fittings for gas, water, sewer, and cable systems, as well as polyurethane foam-insulated pipes, spiral-wound pipes up to three meters in diameter, and polymer manholes. To strengthen its market leadership, ICAPLAST places special emphasis on the development and implementation of cutting-edge technologies.
Photos
Products
-
MEP systemsPolymer wells
ICAPLAST polymer manholes for sewerage, drainage and water supply: welded models made of PP corrugated pipes, rotationally molded DN1000/DN1500 and manholes with a shaft made of SVT DN1000–DN3000.
-
MEP systemsSUNSET corrugated pipes
SUNSET corrugated pipes made of IKAPLAST polypropylene are designed for outdoor gravity sewer, stormwater, and drainage systems. Four ring stiffness classes—SN8, SN10, SN16, and SN24—cover a wide range of installation conditions, from residential sewers to airports and industrial facilities. Diameters range from 110 to 1000 mm, and lengths reach 6000 mm. The smooth inner layer maintains self-cleaning flow, and the service life is at least 50 years.
-
MEP systemsAQUASAFE pipes
ICAPLAST produces pressure polyethylene pipes for outdoor cold water supply and wastewater disposal systems. The AQUASAFE line offers diameters from 20 to 1200 mm, single- and multi-layer wall construction, and versions with a protective sheath.
-
MEP systemsGas supply pipes
ICAPLAST polyethylene gas pipeline pipes made of PE 100 and PE 100 RC: single-layer and multilayer ML II, ML III, with or without a PS protective sheath. Diameters 20-630 mm, SDR 11 and SDR 17. Certified in the Gazsert system. For underground low- and medium-pressure gas distribution networks.
-
MEP systemsPipes for cable networks ELECTROSAFE
ELECTROSAFE conduits for mechanical protection of underground cable lines. They are used to protect control and power cables from mechanical impacts, dynamic and static loads, and aggressive environmental factors.
-

TITAN pressure pipes
A specialized line from the IСAPLAST pipe plant for use in conditions of intense hydroabrasive wear and aggressive chemical environments. The 2–10 mm inner wear-resistant layer, applied using a coextrusion method, absorbs abrasive impact and significantly increases the service life of the pipeline compared to single-layer PE 100 pipe. Diameters from 110–1200 mm, pressure up to 25 bar.
-
MEP systemsPolymer pipes in polyurethane foam insulation
ICAPLAST polyurethane foam-insulated polymer pipes: ALPHA and CELSIUM pressure pipes, JUPITER non-pressure corrugated pipes, and PE-ND jacket pipes for pre-insulated steel pipelines. They are used in water supply, heating, and sewerage systems, including in the Far North. Suitable for underground, aboveground, and aboveground installation.
-
MEP systemsSpiral-wound pipes
Spiral-wound pipes (SVT) made of ICAPLAST polyethylene are used in main sewers, storm drains, industrial pipelines, utility tunnels, and for the rehabilitation of worn-out networks using the pulling method. Diameters range from 1000 to 3000 mm, ring stiffness ranges from SN4 to SN16. Structured hollow wall with a closed profile.
-
MEP systemsShaped products
ICAPLAST PE 100, PE 100 RC, and PE 100+ fittings for pressure water supply and sanitation pipelines: welded elbows, equal and unequal tees, crosses, reducers, flange bushings, protective couplings, and monolithic fittings for installation in manholes. Diameters 63-1200 mm, SDR 11-17. GOST R 70628.3-2023, TU 22.21.29-001-50049230-2025.








